KOOLTHERM K17 PDF

KOOLTHERM K17 PDF

The wall dry–lining insulation shall be Kingspan Kooltherm® K Insulated Dry– lining Board comprising a mm plasterboard facing bonded to ____mm. Kingspan Kooltherm K Super high performance rigid thermoset phenolic insulation; Fibre-free, closed cell insulation core; 3-in-1 insulation, dry-lining and . Kooltherm K17 Insulated Dry-lining Board is an insulated plasterboard for traditional dot and daube plaster adhesive fixing. The tapered edge board enables flat.

Author: Nikok Fenrigor
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Marketing
Published (Last): 18 April 2006
Pages: 457
PDF File Size: 16.89 Mb
ePub File Size: 5.26 Mb
ISBN: 115-8-25501-406-1
Downloads: 48322
Price: Free* [*Free Regsitration Required]
Uploader: Vudoran

Kooltherm K17 Insulated Plasterboard.

Kooltherm K17 Insulated Plasterboard | Wall Insulation | Kingspan | New Zealand

The wall should be kk17, dry and level as surface irregularities may impede fixing of the board. However, it is recommended that any spills be cleaned off fully before the boards are installed. Vertical dabs of the gypsum adhesive are progressively applied to the background together with a continuous fillet at skirting and ceiling level.

Fixing should employ the same method as is used for the plain wall areas.

Tapered edged boards koooltherm the employment of standard dry—lining techniques. Ensure that the blobs adjacent to a board joint are approximately 25 mm in from the edge to avoid bridging the joint.

Kingspan Kooltherm K17 Insulated Plasterboard

The reverse facing of K17 Insulated Plasterboard is a tissue based facing autohesively bonded to the insulation core during manufacture. This will necessitate the use of koolthrem placed between the joists to coincide with the long edges of the board.

This method is for application to fair finished brick, block and concrete cavity walls where K17 is to be finished with gypsum plaster. The timbers should run vertically and be wide kooltuerm to offer a minimum 20 mm support to all four edges of the board.

  ANSYS BLADEMODELER PDF

The Old Stone House Aged not by years, but by its stories. Please click “Accept and close” to accept the use of cookies on our website.

Cutting should be carried out either by using a fine toothed saw, or by scoring with a sharp knife, snapping the board over a straight edge and then cutting the facing on the other side. The frame should be set vertically at a maximum of mm centres to coincide with board joints and midpoint of board. Heavy surface mounted fittings will require provision for the fixing load to be applied direct to the supporting wall and not to the K17 in isolation.

This method is for application to sound, plane concrete or plastered wall surfaces on cavity walls. Ensure that the wall surface to be bonded to is free from oil, grease, paint, release agent, or any contaminate that may affect the bond of the adhesive to the wall.

Water Vapour Resistance Modified to include board facings, the boards achieve a resistance far greater than MN.

Kingspan K17 Kooltherm Phenolic Thermal Laminate Plaster Dab

Where adhesives are employed, soffit boards and boards at window heads should be temporarily supported. Test – BS —7: Finishing Tapered edged boards allow the employment of standard dry—lining techniques. Damaged boards or boards that have been in contact with harsh solvents or acids should not be used.

A plaster skim finish can also be applied to the boards. K17 Insulated Dry—lining Board has a gypsum plasterboard face. Ensure that safe methods of cleaning are used, as recommended by the suppliers of the spilt liquid.

INSULATION

Construction Adhesive Bonding View Instructions. Its durability depends on the supporting structure and the conditions of its use. Gun apply a continuous blob of construction adhesive around perimeter wall and ceiling junctions, and around any openings, such as windows and doors, in order to provide a seal.

  74HC08N DATASHEET PDF

Please note that the reflective surfaces on this product are designed to enhance their thermal performance. Product Information Contact Us.

Tap the board back firmly using a straightedge, ensuring that the vertical edge is plumb. Our teams are dedicated to helping you make process as easy as possible and ensure you get the right materials for your needs. Proprietary Adhesive Bonding This method is for application to sound, plane concrete or plastered wall surfaces on cavity walls. It is recommended that mechanical fixings are positioned in the tapered edge of the boards so that they are covered when the board is finished, e.

Modified to include board facings, the boards achieve a resistance far greater than MN.

Cutting Cutting should be carried out either by using a fine toothed saw, or by scoring with a sharp knife, snapping the board over a straight edge and then cutting the facing oooltherm the other side. Pricing and Where to Buy.

Mechanical Fixing to Metal Furring Systems K17 Insulated Plasterboard can be fixed by the use of proprietary metal framing systems to brick, block or concrete walls. Kingspan Insulation New Zealand We’re ready to help.

On existing constructions all surfaces should be clean and free of loose or flaking materials.